Dr.Pulley HiT Clutch fit Yamaha Rhino Grizzly Rhino Access 700 HIGH PERFORMANC

Description

Dr.Pulley high performance clutch HiT 301502_V4
(new model Super 2013
)
clutch bell diameter 150mm
In the Dr.Pulley HiT clutch two sets of springs are working: The clutch spring, inside, controls through the centrifugal power the movement of the clutch pads towards the clutch bell (for example at 3000 rpm).
The second set of "torque" springs, externally mounted, controls then the pressure by using a "push pin" on the clutch linings (in the example already at 3400 rpm) against the bell, thus preventing most of the slipping phase of the clutch.
Because of less friction, much less heat is generated. heat is lost power.
The ATV accelerates much faster because the full power transmission to the rear tyre
already exists
at 3,400 rpm, instead of 4000rpm with a normal clutch.
The HiT clutch is
very effective while driving with frequent speed changings: To accelerate out of curves or at mountain trips.
Or for a powerful overtaking.
The
graphs
show a marked increase in speed and performance especially in low and medium speed ranges.
With the two fully enclosed
sets of
spring , the clutch can be customized to all personal needs.
For example, if you want to get more power at start, choose a stronger clutch spring to increase the starting rpm.
If you want to shorten the slipping phase of the clutch, you should select a weaker pillow (torque) spring.
Extreme: To get an extreme start (wheely), choose a strong clutch spring, and a very weak (or no) pillow (torque) spring.
For those who do not want to experiment long, an average spring combination
is already installed
with delivery
.
Importatant: Together with the HiT high performance clutch the use of not too light vario weights is strongly recommended. The best result you get with Dr.Pulley slider rolls with the same weight like the original or 5-10% lighter.
Delivery:
HiT high-performance clutch, depending on the model with 3 or 4 clutch pads
Minimum of 3 complete sets of clutch springs and torque (pillow) springs
"Washer" rings to increase the pressure of the counter-pressure spring
Spare pins and springs, sticker, instructions,
link to the HiT manual
Fits the following Scooters / Scooter / ATV (
see also Dr.Pulley Forum
)
Quads/ATV
Yamaha Rhino Grizzly Rhino Access 700
The grip force comes not only from the centrifugal force and the friction
coefficient of clutch weight, but most importantly from the compression
mechanism—push pin & pillow system of HiT Clutch.
Better engine response, stronger grip force.
No more deformed and blued clutch bell.Improving the acceleration performance and engine response when re-acceleration. Better steel quality
Step 1: The clutch weight is driven to rotate but the initial rev is not high enough, so the clutch weight and the bell are in non-contacting
state (Fig.2.)
Step 2: When the rotating speed of HiT Clutch is high enough, the clutch weight will centrifugally fly outward to touch the clutch
bell to proceed the initial slippery clutch-in. The clutch weight is slippily contacting with the bell but the push pin is unactuated yet (Fig.3).
The friction resistance is produced between the clutch wear pad and the inner surface of clutch bell during the stage of slippery clutch-in.
Step 3: When the friction resistance is higher than the predetermined distortion strength of pillow spring, the pillow spring will be deformed or extended, and the push pin will thrust into the pillow to compress the clutch weight to grab the clutch outer very tightly. (Fig.4, the push pin is actuated and pressed against the pillow)
A lot cheaper, and cheaper shipping. Please ask
me
Make sure
the model
and asked
me
Taiwan Motorcycle Parts
We are Taiwan motorbike parts dealer
We have modification parts & Taiwan's bike genuine parts(Kymco Sym Yamaha motor Taiwan Suzuki Taiwan)